OrangePi 2G-IOT: No boot with 16GB microSDHC UHS-I Class 10 (ADATA)

jmoeller · Published in 2017-5-10 06:47:13

tpickle replied at 2017-5-10 05:55
Check out this thread

Thanks, I did find that and now I am able to get it to repeated boot. I was able to get another of my cards to boot using the Ubuntu Server image. On both of the cards that work with Ubuntu, neither worked with the other linux builds.
Just for the record, the command he listed gave an error for me, but running

sudo apt-get purge alsa-utils

Copy code

worked for me.

Good luck all. Now to try and get the 2G working.

tpickle · Published in 2017-5-10 07:37:26

jmoeller replied at 2017-5-10 06:47
Thanks, I did find that and now I am able to get it to repeated boot. I was able to get another o ...

Yup, i remember having to modify the command to. Thanks for posting it. I couldnt post to forum when i found the fix. I am playing catch up. I also am working on 2G.

lavAzza · Published in 2017-5-11 23:38:22

jmoeller replied at 2017-5-5 22:48
I am having the same issue. I have tried multiple different cards and multiple Linux images. Non ...

The same problem...
I tryed 8Gb 10class noname micro sd card and 16Gb 10class Samsung micro sd card with both linux image. The power led was off.
And I connected USB-TTL converter, with no result.

tpickle · Published in 2017-5-13 09:43:08

lavAzza replied at 2017-5-11 23:38
The same problem...
I tryed 8Gb 10class noname micro sd card and 16Gb 10class Samsung micro sd ca ...

lavAzza -

What output are you getting from your console/tty?

lavAzza · Published in 2017-5-15 12:50:41

tpickle replied at 2017-5-13 09:43
lavAzza -

No any output on 115200.

czarny · Published in 2017-5-15 20:47:07

Edited by czarny at 2017-5-15 20:48

I cannot boot Armbian from SD card too. The same problem occurs on several SD cards.
Here is terminal output on 921600

RDA8810 Boot_ROM V1.6
HW_CFG: 4286
SW_CFG: 0000
Load EMMC
Open eMMC
EMMC OCR timeout
Open eMMC card Failed
Load EMMC Fail
Load SD
Open SD card
mcd_Open
Response is Time out
ACMD xx Response Error
ACMD41, Retry Timeout
Open SD card Failed
Load SD Fail
Setup USB PLL done
Setup BUS PLL done
Press ‘Q’ to quit PDL loading
wait for connect....

Copy code

snouhaud · Published in 2017-5-16 18:03:08

Edited by snouhaud at 2017-5-16 18:04

Hi,

I have same trouble with booting after find SD Card that Work (Samsung Evo+ 32Go HC I)

The PI boot (last image of ubuntu 16.04 1.1) on SD Card but stop with this message (output capture on serial 921600bps) with :

RDA8810 Boot_ROM V1.6
HW_CFG: 0286
SW_CFG: 0000
Load EMMC
Open eMMC
EMMC OCR timeout
Open eMMC card Failed
Load EMMC Fail
Load SD
Open SD card
mcd_Open
Card is SDHC
Inserted Card is a SD card
mcd_Open Done
Loading image from SD card ................................................................................................Done
Check Image ... Done
Run ...
Init Clock ...
Clock config ver: 1.0
PMU vbuck1 = 9, vbuck3 = 10
setup ddr vtt to 1
setup ddr vtt to 1
setup ddr vtt to 1
setup ddr vtt to 1
setup ddr vtt to 1
setup ddr vtt to 1
setup ddr vtt to 1
setup ddr vtt to 1
setup ddr vtt to 1
rda2 stand for dqs_prsel_preset
rda2=0 rda2=1 rda2=2 rda2=3 rda2=4 rda2=5 rda2=6 rda2=7
R R R R * * R R
Please check the result and choose the best one
final rda2= 0, rda2_old = 2
setup ddr vtt to 1
pll freq CPU = 988
pll freq BUS = 800
pll freq MEM = 260
Init DDR, flag = 0x0002, para = 0x00001338
32bit dll-on Mode ...
ddr2 phy init done!
format ctrl value: 22000202
address ctrl value: 30301
decode ctrl value: 10
dram init done ...
Done
SETTING SECURITY CONTEXT
Board security: Not present
Init emmc ...
MMC: registered mmc interface 0
Spl init emmc first, use default zero mclk adj and inv.
MMC: registered mmc interface 1
raise: Signal # 8 caught
ERROR: v7_dcache_inval_range - stop address is not aligned - 0x0010f948
-------------MMC information-----------
Manufacturer ID: 1b, Name: Unknown
OEM: 534d
Tran Speed: 25000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: Bus Width: 4-bit
-----------------------------------------
boot_mmc mfr id = 1b
EMMC boot ...
response timeout
mmc fail to send stop cmd
spl emmc read err 0
Check Image ...Verify image:
Done
U-Boot 2012.04.442-rel5.0.2 (Apr 23 2017 - 17:38:39)
RDA8810 SoC
Board: RDA8810
DRAM: 236 MiB
CPU: enable instruction caches
CPU: enable data caches
CPU: enable neon
CPU: p15-c1-c1 (NSACR): 0x00000000 -> 0x00000c00
CPU: p15-c1-c0 (CPACR): 0x00000000 -> 0x00f00000
NAND: metal 28 hwcfg 286, use eMMC, skip nand init
0 MiB
MMC: MMC: registered mmc interface 0
Cannot find the emmc corresponding mclk adj and inv.Now use default zero. Please add it
MMC: registered mmc interface 1
ERROR: v7_dcache_inval_range - stop address is not aligned - 0x8dae6aa8
-------------MMC information-----------
Manufacturer ID: 1b, Name: Unknown
OEM: 534d
Tran Speed: 25000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: Bus Width: 4-bit
-----------------------------------------
MMC: 0, MMC: 1
Using default environment
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0
Board Mux : Done.
mmc0 is current device
Loading file "boot.scr" from mmc device 0:1 (xxa1)
884 bytes read
## Executing script at 81000000
** No boot file defined **
Loading file "uInitrd" from mmc device 0:1 (xxa1)
data transfer timeout
** ext2fs_devread read error - block
** Unable to read "uInitrd" from mmc 0:1 **
response timeout
** Can't read partition table on 0:0 **
** Bad partition 1 **
response timeout
** Can't read partition table on 0:0 **
** Bad partition 1 **
## Checking Modem Code Image at 80000000 ...
Verifying Image Header ... Bad Magic Number
## Waiting for modem response ...
## Warning: Timeout when waiting for modem response. Press Ctrl-C to abort.

Copy code

someone else have same trouble ?

Regards

snouhaud · Published in 2017-5-17 23:30:51

Forget my previous message... I just have used UnetBootin for prepare the SD Card and he add a specific bootloader to SD Card. it's an error from my sd card preparation.

Read in last documentation (0.9.5) that IOT 2G work only with 8G Class 10 SD Card... waiting to receive this type of SD

tpickle · Published in 2017-5-19 07:50:27

snouhaud replied at 2017-5-17 23:30
Forget my previous message... I just have used UnetBootin for prepare the SD Card and he add a speci ...

I will try my 16g class 10 next to see if i get same boot message this weekend.

malvcr · Published in 2017-5-20 10:39:50

malvcr replied at 2017-4-30 06:46
I have one of my 2G-IOT working with a Lexar 8G Class 10 card, manually resized to full capacity usi ...

As an extra reference:

I have been working with several 2G-IOT machines, and all them have differen issues. Have been complicated to find some correlation trying to resolve the booting process, but this is what I know.

1) 16 GB class 10 SD cards don't work ( I used three brand new Ultra SD SanDisk class 10 cards ... all them fail, and a Radio Shack class 10 also fail ). No matter what OS image you use.
2) 4 GB class 4 SD card from SanDisk also fail.
3) 8 GB Lexar class 10 seens to work ... three different cards, two work and one fail ... although the failing could be damaged.

Then maybe the problem is not the "class 10" but the size.

Also, I boot from an Armbian image and although it do something, it seems that some internal library is damaged; so, it is possible that some provided images have issues independently of any incompatibility with the particular card type.

Somebody else could sumarize experiences to see if we can decode this mistery?