OPiOne Not Bootting

Matt_Edwards

I have been trying to get various images to work on my OPI One in thisthread.I think one of my bards has developed an issue.
I am using a 5V 8Amp SMPS.
When I start up with the Serial debug I get the following result

1. U-Boot SPL 2016.09-armbian (Sep 15 2016 - 07:19:14)
   
2. DRAM: 512 MiB
   
3. Trying to boot from MMC1
   
4. 
   
5. 
   
6. U-Boot 2016.09-armbian (Sep 15 2016 - 07:19:14 +0200) Allwinner Technology
   
7. 
   
8. CPU:   Allwinner H3 (SUN8I 1680)
   
9. Model: Xunlong Orange Pi One
   
10. DRAM:  512 MiB
    
11. MMC:   SUNXI SD/MMC: 0
    
12. *** Warning - bad CRC, using default environment
    
13. 
    
14. In:    serial
    
15. Out:   serial
    
16. Err:   serial
    
17. Net:   phy interface0
    
18. eth0: ethernet@1c30000
    
19. Hit any key to stop autoboot:  0
    
20. switch to partitions #0, OK
    
21. mmc0 is current device
    
22. Scanning mmc 0:1...
    
23. Found U-Boot script /boot/boot.scr
    
24. 2886 bytes read in 143 ms (19.5 KiB/s)
    
25. ## Executing script at 43100000
    
26. gpio: pin PL10 (gpio 298) value is 1
    
27.    Warning: value of pin is still 0
    
28. gpio: pin PG11 (gpio 203) value is 1
    
29. ** File not found /boot/.verbose **
    
30. ** File not found /boot/.next **
    
31. ** Unrecognized filesystem type **
    
32. ** File not found .next **
    
33. 35908 bytes read in 405 ms (85.9 KiB/s)
    
34. 3114523 bytes read in 307 ms (9.7 MiB/s)
    
35. 5025168 bytes read in 451 ms (10.6 MiB/s)
    
36. ## Loading init Ramdisk from Legacy Image at 43300000 ...
    
37.    Image Name:   uInitrd
    
38.    Image Type:   ARM Linux RAMDisk Image (gzip compressed)
    
39.    Data Size:    3114459 Bytes = 3 MiB
    
40.    Load Address: 00000000
    
41.    Entry Point:  00000000
    
42.    Verifying Checksum ... OK
    
43. Using machid 0x1029 from environment
    
44. 
    
45. Starting kernel ...
    
46. 
    

Copy code

If I power cycle the board,  the follow line repeat a lot after Starting Kernel

1. U-Boot SPL 2016.09-armbian (Sep 15 2016 - 07:19:14)
   
2. DRAM: 512 MiB
   
3. Trying to boot from FEL

Copy code

Any ideas if I can fault find this board?  
( I am a Linux newby but will investigate as much as I can).

shooreg

Have  you used a correct script.bin and uImage for your OPI ONE?

Matt_Edwards

Yes.  I have two OPI One boards.  I use the same image on both. One boards works exactly as expected.  I have tried the same new 16G SD card in both boards.

shooreg

Can you compare the u-boot output from two boards?