Ubuntu_Vivid_Mate does not boot on Orange Pi PC

m.capurso

Hello, Loboris. Thanks for your good work.
I bought an Orange PI PC and tried to follow your suggestions on your post.
I downloaded OrangePI-PC_Ubuntu_Vivid_Mate.img prepared for OrangePI users, just copy to SDCard, no configuration needed !

I  copied to SD card with win32 disk imager , then I linked an USB to TTL cable to rx/tx and I put the SDCard in the
Orange PI PC.
The boot messages were as follow, but nothing appears on HDMI
and nothing more appears on the serial.

What is wrong ?

HELLO! BOOT0 is starting!
boot0 version : 4.0.0
fel_flag = 0x00000000
rtc[0] value = 0x00000000
rtc[1] value = 0x00000000
rtc[2] value = 0x00000000
rtc[3] value = 0x00000000
rtc[4] value = 0x00000000
rtc[5] value = 0x00000000
rtc[6] value = 0x00000000
rtc[7] value = 0x00000000
DRAM DRIVE INFO: V0.8
DRAM Type = 3 (2DR2,3DR3,6PDDR2,7PDDR3)
DRAM CLK = 672 MHz
DRAM zq value: 003b3bfb
READ DQS LCDL = 001d1c1e
DRAM SIZE =1024 M
odt delay
dram size =1024
card boot number = 0
card no is 0
sdcard 0 line count 4
[mmc]: mmc driver ver 2014-12-10 21:20:39
[mmc]: ***Try SD card 0***
[mmc]: SD/MMC Card: 4bit, capacity: 15193MB
[mmc]: vendor: Man 00035344 Snr 000e8443
[mmc]: product: SS16G
[mmc]: revision: 8.0
[mmc]: ***SD/MMC 0 init OK!!!***
sdcard 0 init ok
The size of uboot is 000dc000.
sum=ede66ee7
src_sum=ede66ee7
Succeed in loading uboot from sdmmc flash.
Ready to disable icache.
Jump to secend Boot.
SUNXI_NORMAL_MODE   
already secure mode

[      0.376]

U-Boot 2011.09-rc1 (Jun 21 2015 - 19:33:17) Allwinner Technology

[      0.383]version: 1.1.0
normal mode
[      0.391]pmbus:   ready
not set main pmu id
axp_probe error
[      0.406]PMU: pll1 1200 Mhz,PLL6=600 Mhz
AXI=400 Mhz,AHB=200 Mhz, APB1=100 Mhz
sid read already
fel key new mode
run key detect
no key found
no key input
dram_para_set start
dram_para_set end
normal mode
[      0.437]DRAM:  1 GiB
relocation Offset is: 35af9000
[box standby] read rtc = 0x0
[box_start_os] mag be start_type no use
user_gpio config
user_gpio ok
gic: normal or no secure os mode
workmode = 0
MMC:     0
[      0.511][mmc]: mmc driver ver 2014-12-10 9:23:00
[      0.516][mmc]: get sdc_phy_wipe fail.
[      0.520][mmc]: get sdc0 sdc_erase fail.
[      0.524][mmc]: get sdc_f_max fail,use default 50000000Hz
[      0.529][mmc]: get sdc_ex_dly_used fail,use default dly
[      0.535][mmc]: SUNXI SD/MMC: 0
[      0.548][mmc]: *Try SD card 0*
[      0.599][mmc]: CID 0x3534453 0x53313647 0x80000e84 0x4300f4d1
[      0.604][mmc]: mmc clk 50000000
[      0.608][mmc]: SD/MMC Card: 4bit, capacity: 15193MB
[      0.613][mmc]: boot0 capacity: 0KB,boot1 capacity: 0KB
[      0.618][mmc]: ***SD/MMC 0 init OK!!!***
[      0.622][mmc]: erase_grp_size:0x1WrBlk * 0x200 = 0x200 Byte
[      0.628][mmc]: secure_feature 0x0
[      0.631][mmc]: secure_removal_type  0x0
[      0.635]sunxi flash init ok
script config pll_de to 864 Mhz
Not Found clk pll_video1 in script
script config pll_video to 297 Mhz
[boot]disp_init_tv
[DISP_TV] disp_init_tv enter g_tv_used
screen 0 do not support TV TYPE!
[BOOOT_DISP_TV] disp tv device_registered
unable to find regulator vcc-hdmi-18 from [pmu1_regu] or [pmu2_regu]
enable power vcc-hdmi-18, ret=-1
DRV_DISP_Init end
boot_disp.auto_hpd=1
auto hpd check has 50 times!
[disk_read_fs] no the partition
error: open disp_rsl.fex, maybe it is not exist
attched ok, mgr1<-->device1, type=2, mode=11----
ready to set mode
disp_tv_enable
[      1.476]finally, output_type=0x2, output_mode=0xb, screen_id=0x1, disp_para=0x20b0000
fail to find part named env
Using default environment

In:    serial
Out:   serial
Err:   serial
--------fastboot partitions--------
mbr not exist
base bootcmd=run setargs_mmc boot_normal
bootcmd set setargs_mmc
key 0
cant find rcvy value
cant find fstbt value
no misc partition is found
to be run cmd=run setargs_mmc boot_normal
[      1.513][mmc]: MMC Device 2 not found
[      1.517][mmc]: Can not find mmc dev
[      1.521][mmc]: read first backup failed in fun sdmmc_secure_storage_read line 1849
sunxi_secstorage_read fail
get secure storage map err
the private part isn't exist
WORK_MODE_BOOT
adver not need show
sunxi_bmp_logo_display
[disk_read_fs] no the partition
error: open bootlogo.bmp, maybe it is not exist
sunxi bmp info error : unable to open logo file bootlogo.bmp
[      1.554]Hit any key to stop autoboot:  3  2  1  0
[      4.813][mmc]: blkcnt should not be 0
[      5.286][mmc]: blkcnt should not be 0
## Booting kernel from Legacy Image at 40007800 ...
   Image Name:   Linux-3.4.39
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    10915552 Bytes = 10.4 MiB
   Load Address: 40008000
   Entry Point:  40008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK
[      5.477][mmc]: MMC Device 2 not found
[      5.481][mmc]:  mmc  not find,so not exit
[      5.485]
Starting kernel ...

fritz

I have seen this error while it hangs on booting the kernel due power supply or micro sd card problems.
Try with another micro Sd card possibly from quality manufacturer class 10 card or with another power supply.

m.capurso

SOLVED. I changed the power adapter. The old one under load decreased voltage to 4.2 V . Used a 5 V 2.5 A . Probably load increases at boot
when cores are activated. In any case I used a Class 4 SD card and it works. Booted OrangePI-PC_Ubuntu_Vivid_Mate.img and Android .
Thank you for your help.