android booting error

asadpt

I was trying to build the android image for orange pi win, and I got the source code from orange pi official website. I was able to build the android image from source code. But it is not booting. I am pasting the log file below.




HELLO! BOOT0 is starting!
boot0 commit : c8cf24d1d34e7621583739b09227f1e3a2ef603b

boot0 version : 4.0.0
set pll start
set pll end
rtc[0] value = 0x00000000
rtc[1] value = 0x00000000
rtc[2] value = 0x00000000
rtc[3] value = 0x00000000
rtc[4] value = 0x00000000
rtc[5] value = 0x00000000
DRAM driver version: V1.0
DRAM Type = 3 (2DR2,3DR3,6PDDR2,7PDDR3)
DRAM clk = 672 MHz
DRAM zq value: 003b3bbb
rsb_send_initseq: rsb clk 400Khz -> 3Mhz
PMU: AXP81X
ddr voltage = 1500 mv
DRAM single rank full DQ OK
DRAM size = 1024 MB
DRAM init ok
dram size =1024
card boot number = 0, boot0 copy = 0
card no is 0
sdcard 0 line count 4
[mmc]: mmc driver ver 2015-05-08 20:06
[mmc]: sdc0 spd mode error, 2
[mmc]: Wrong media type 0x00000000
[mmc]: ***Try SD card 0***
[mmc]: HSSDR52/SDR25 4 bit
[mmc]: 50000000 Hz
[mmc]: 15193 MB
[mmc]: ***SD/MMC 0 init OK!!!***
sdcard 0 init ok
The size of uboot is 000f8000.
sum=2256d661
src_sum=2256d661
Succeed in loading uboot from sdmmc flash.
boot0: start load other image
boot0: Loading BL3-1
Loading file 0 at address 0x40000000,size 0x0000a400 success
boot0: Loading scp
Loading file 2 at address 0x00040000,size 0x00019c00 success
set arisc reset to de-assert state
Ready to disable icache.
Jump to secend Boot.%9=é    Configuring SPC Controller
NOTICE:  BL3-1: v1.0(debug):c8cf24d
NOTICE:  BL3-1: Built : 19:28:18, Jul  8 2015
NOTICE:  BL3-1 commit: c8cf24d1d34e7621583739b09227f1e3a2ef603b

INFO:    BL3-1: Initializing runtime services
INFO:    BL3-1: Preparing for EL3 exit to normal world
INFO:    BL3-1: Next image address = 0x4a000000
INFO:    BL3-1: Next image spsr = 0x1d3


U-Boot 2014.07 (Sep 16 2015 - 18:08:34) Allwinner Technology

uboot commit : ad5f4db37d600c2566902ed7e243eaa9b670a563

rsb: secure monitor exist
[      0.385]pmbus:   ready
[      0.387][ARISC] :arisc initialize
[      0.715][ARISC] :arisc_dvfs_cfg_vf_table: support only one vf_table
[SCP] :sunxi-arisc driver begin startup 2
[SCP] :arisc_para size:1a8
[SCP] :arisc version: [v0.1.76]
[SCP] :sunxi-arisc driver v1.10 is starting
[      0.841][ARISC] :sunxi-arisc driver startup succeeded
[      0.874]PMU: AXP81X
[      0.876]PMU: read AXP81X 84H=0xf6
[      0.879]PMU: write AXP81X 84H=0xf6
[      0.883]PMU: AXP81X found
bat_vol=0, ratio=100
[      0.889]PMU: dcdc2 1100
[      0.892]PMU: cpux 1008 Mhz,AXI=336 Mhz
PLL6=600 Mhz,AHB1=200 Mhz, APB1=100Mhz AHB2=300Mhz MBus=400Mhz
device_type = 3253, onoff=1
dcdc1_vol = 3100, onoff=1
dcdc2_vol = 1100, onoff=1
dcdc6_vol = 1100, onoff=1
aldo1_vol = 2800, onoff=0
aldo2_vol = 1800, onoff=1
aldo3_vol = 3000, onoff=1
dldo1_vol = 3300, onoff=0
dldo2_vol = 3300, onoff=0
dldo3_vol = 2800, onoff=0
dldo4_vol = 3300, onoff=1
eldo1_vol = 1800, onoff=1
eldo2_vol = 1800, onoff=0
eldo3_vol = 1800, onoff=0
fldo2_vol = 1100, onoff=1
gpio0_vol = 3100, onoff=0
vbus not exist
no battery, limit to dc
DRAM:  1008 MiB
fdt addr: 0x76eb8740
Relocation Offset is: 35f0a000
In:    serial
Out:   serial
Err:   serial
gic: sec monitor mode
[      1.162]start
drv_disp_init
init_clocks: finish init_clocks.
fdt_get_one_gpio lcd0.lcd_gpio_0 fail
fdt_get_one_gpio lcd0.lcd_gpio_1 fail
fdt_get_one_gpio lcd0.lcd_gpio_2 fail
fdt_get_one_gpio lcd0.lcd_gpio_3 fail
fdt_get_one_gpio lcd0.lcd_gpio_scl fail
fdt_get_one_gpio lcd0.lcd_gpio_sda fail
enable power vcc-hdmi-33, ret=0
drv_disp_init finish
boot_disp.output_disp=0
boot_disp.output_type=1
boot_disp.output_type=4
fetch script data boot_disp.auto_hpd fail
disp0 device type(1) enable
enable power vcc-dsi-33, ret=0
disp 0, clk: pll(618000000),clk(618000000),dclk(103000000) dsi_rate(103000000)
     clk real:pll(616846153),clk(616846153),dclk(154211538) dsi_rate(148500000)
enable power vcc-mipi, ret=0
FDT ERROR:fdt_get_pin_num:get property handle pinctrl-0 error:<unknown error>
disp_sys_pin_set_state, fdt_set_all_pin, ret=-1
[      1.730]end
workmode = 17,storage type = 1
[      1.734]NB1 : enter phy init
[      1.737]nand_physic_init
[      2.141]Reset NDFC start 0  0
[      2.144]Reset NDFC end 0  0
[      2.147]nand not support! channel 0 chip 0: 00 00 00 00 00 00 00 00
[      2.154]nand not support! channel 0 chip 1: 00 00 00 00 00 00 00 00
[      2.160]nand not support! channel 0 chip 2: 00 00 00 00 00 00 00 00
[      2.167]nand not support! channel 0 chip 3: 00 00 00 00 00 00 00 00
[      2.173] no nand found !
[      2.176]nand_physic_init nand_build_nsi error
[      2.180]nand_physic_init error -1
NB1 : nand phy init fail
[      2.186]NB1 : enter phy Exit
[      2.189]nand_physic_exit
try nand fail
try nand fail
try card 2
[mmc]: mmc driver ver 2015-07-29 14:10:00
[mmc]: get sdc_ex_dly_used 2, use auto tuning sdly
[mmc]: current is product mode, it will tune sdly later
[mmc]: card2 io is 1.8V.
SUNXI SD/MMC: 2
[mmc]: start mmc_calibrate_delay_unit, don't access device...
[mmc]: delay chain cal done, sample: 200(ps)
[mmc]: delay chain cal done, ds: 208(ps)
[mmc]: ************Try SD card 2************
[mmc]: mmc send if cond failed
[mmc]: send app cmd failed
[mmc]: ************Try MMC card 2************
[mmc]: read op condition failed
[mmc]: mmc send op cond failed
[mmc]: read op condition failed
[mmc]: mmc send op cond failed
[mmc]: Card did not respond to voltage select!
[mmc]: ************SD/MMC 2 init error!************
[mmc]: mmc_init: mmc init fail, err -17
MMC init failed
try emmc fail
initcall sequence 7ff9f81c failed at call 4a00c068
### ERROR ### Please RESET the board ###






I have reset the board 4-5 times. but still getting the same log.
please help....

kanehad12

Whether you need advice on the best tool for your specific project or have questions about a particular product, our experts are just a phone call away.
https://adamtoolsmart.com/best-surface-grinder/

CarlosFincher

Looking for cheap coursework writing options? While affordability is important, make sure not to compromise on quality. Some websites may offer low prices, but they might lack experienced writers and deliver subpar content, impacting your academic outcomes.

emmausa

Great blog, thank you for sharing such new and useful information. The Password Game