how to use second spi on OPi one?

port_man

Hi,
I've an OPi one board. It has 2 spi interfcae. one of them is connected to CON3 but not all 4 pins of the other is connected to CON3!

is it possible to change the spi1 default pins in fex file to other pins that are connected to CON3?

I tried to use PA00 ... PA03 for spi1 pins but after converting fex 2 bin, spidev1.0 is not added to device list?
the fex file after my changes look like below:

1. 
   
2. [uart2]
   
3. uart_used = 0
   
4. uart_port = 2
   
5. uart_type = 2
   
6. uart_tx = port:PA00<2><1><default><default>
   
7. uart_rx = port:PA01<2><1><default><default>
   
8. uart_rts = port:PA02<2><1><default><default>
   
9. uart_cts = port:PA03<2><1><default><default>
   
10. 
    
11. [uart3]
    
12. uart_used = 0
    
13. uart_port = 3
    
14. uart_type = 4
    
15. uart_tx = port:PA13<3><1><default><default>
    
16. uart_rx = port:PA14<3><1><default><default>
    
17. uart_rts = port:PA15<3><1><default><default>
    
18. uart_cts = port:PA16<3><1><default><default>
    
19. 
    
20. [spi0]
    
21. spi_used = 1
    
22. spi_cs_bitmap = 1
    
23. spi_mosi = port:PC00<3><default><default><default>
    
24. spi_miso = port:PC01<3><default><default><default>
    
25. spi_sclk = port:PC02<3><default><default><default>
    
26. spi_cs0 = port:PC03<3><1><default><default>
    
27. 
    
28. [spi1]
    
29. spi_used = 1
    
30. spi_cs_bitmap = 1
    
31. spi_mosi = port:PA00<2><default><default><default>
    
32. spi_miso = port:PA01<2><default><default><default>
    
33. spi_sclk = port:PA02<2><default><default><default>
    
34. spi_cs0 = port:PA03<2><1><default><default>
    
35. 
    
36. [spi_devices]
    
37. spi_dev_num = 2
    
38. 
    
39. [spi_board0]
    
40. modalias = "spidev"
    
41. max_speed_hz = 33000000
    
42. bus_num = 0
    
43. chip_select = 0
    
44. mode = 0
    
45. full_duplex = 1
    
46. manual_cs = 0
    
47. 
    
48. [spi_board1]
    
49. modalias = "spidev"
    
50. max_speed_hz = 33000000
    
51. bus_num = 1
    
52. chip_select = 0
    
53. mode = 0
    
54. full_duplex = 1
    
55. manual_cs = 0

Copy code

command I used:

1. sudo mount /dev/mmcblk0p1 /mnt/
   
2. bin2fex /mnt/script.bin /tmp/orange.fex
   
3. sudo nano /tmp/orange.fex
   
4. sudo fex2bin /tmp/orange.fex /mnt/script.bin
   
5. sudo reboot
   
6. ls /dev/s*

Copy code

bozden

I'm new to this, but aren't those PORT <=> PIN definitions defined by hardware?

abdulmoeez

I high appreciate this post. It’s hard to find the good from the bad sometimes, but I think you’ve nailed it! would you mind updating your blog with more information?        slot online

abdulmoeez

Nice blog and absolutely outstanding. You can do something much better but i still say this perfect.Keep trying for the best.        Tgv trike

abdulmoeez

An fascinating discussion is value comment. I think that it is best to write extra on this matter, it won’t be a taboo topic however generally people are not enough to talk on such topics. To the next. Cheers        สล็อต