New orange pi pc doesn't boot

laniel · Published in 2016-3-15 11:45:01

Hello to every body i am a new member here and this is my first post, please i need a help before fiew days i have receive two orange pi pc from Banggood but one of them never working doesn't boot still remain to H3 logo. Tried with several SD cards, different images (android downloaded from Orange Pi site), even tried with different HDMI cables and monitors. Doesn't boot

i have write to banggood and send photos and video about for my problem and they say to show my problem here. the other one is working fine
thank you very much

laniel · Published in 2016-3-16 16:19:35

please any help for my problem?

javax · Published in 2016-4-4 21:41:41

I captured this data down in my orangepi PC by serial, apparently dead whem i use armbian images. I noticed that it's as if he does not recognize the partition data . but this same card works perfectly on another PC orangepi I have.

Messages of serial:

U-Boot 2016.03-rc2-armbian (Mar 08 2016 - 20:18:51 +0100) Allwinner Technology

CPU: Allwinner H3 (SUN8I)
I2C: ready
DRAM: 1 GiB
MMC: SUNXI SD/MMC: 0
*** Warning - read failed, using default environment
In: serial

Out: serial

Err: serial

Net: No ethernet found.

starting USB...

No controllers found

Hit any key to stop autoboot: 2 1 0

switch to partitions #0, OK

mmc0 is current device

** No partition table - mmc 0 **

starting USB...

No controllers found

USB is stopped. Please issue 'usb start' first.

starting USB...

No controllers found

No ethernet found.

missing environment variable: pxeuuid

missing environment variable: bootfile

Retrieving file: pxelinux.cfg/00000000

No ethernet found.

missing environment variable: bootfile

Retrieving file: pxelinux.cfg/0000000

No ethernet found.

missing environment variable: bootfile

Retrieving file: pxelinux.cfg/000000

No ethernet found.

missing environment variable: bootfile

Retrieving file: pxelinux.cfg/00000

No ethernet found.

missing environment variable: bootfile

Retrieving file: pxelinux.cfg/0000

No ethernet found.

missing environment variable: bootfile

Retrieving file: pxelinux.cfg/000

No ethernet found.

missing environment variable: bootfile

Retrieving file: pxelinux.cfg/00

No ethernet found.

missing environment variable: bootfile

Retrieving file: pxelinux.cfg/0

No ethernet found.

missing environment variable: bootfile

Retrieving file: pxelinux.cfg/default-arm-sunxi

No ethernet found.

missing environment variable: bootfile

Retrieving file: pxelinux.cfg/default-arm

No ethernet found.

missing environment variable: bootfile

Retrieving file: pxelinux.cfg/default

No ethernet found.

Config file not found

starting USB...

No controllers found

No ethernet found.

javax · Published in 2016-4-4 21:42:30

whem i use from loboris OrangePI-PC_Ubuntu_Vivid_Mate.img , appears this message.

U-Boot 2011.09-rc1 (Jun 21 2015 - 19:33:17) Allwinner Technology

[    0.353]version: 1.1.0
normal mode
[    0.361]pmbus: ready
not set main pmu id
axp_probe error
[    0.376]PMU: pll1 1200 Mhz,PLL6=600 Mhz
AXI=400 Mhz,AHB=200 Mhz, APB1=100 Mhz
sid read already
fel key new mode
run key detect
no key found
no key input
dram_para_set start
dram_para_set end
normal mode
[    0.406]DRAM:  1 GiB
relocation Offset is: 35af9000
[box standby] read rtc = 0x0
[box_start_os] mag be start_type no use
user_gpio config
user_gpio ok
gic: normal or no secure os mode
workmode = 0
MMC:    0
[    0.480][mmc]: mmc driver ver 2014-12-10 9:23:00
[    0.485][mmc]: get sdc_phy_wipe fail.
[    0.489][mmc]: get sdc0 sdc_erase fail.
[    0.493][mmc]: get sdc_f_max fail,use default 50000000Hz
[    0.498][mmc]: get sdc_ex_dly_used fail,use default dly
[    0.504][mmc]: SUNXI SD/MMC: 0
[    0.517][mmc]: *Try SD card 0*
[    0.550][mmc]: CID 0x3505453 0x53303847 0x30da9f0f 0x2000f92d
[    0.555][mmc]: mmc clk 50000000
[    0.559][mmc]: SD/MMC Card: 4bit, capacity: 7388MB
[    0.563][mmc]: boot0 capacity: 0KB,boot1 capacity: 0KB
[    0.569][mmc]: ***SD/MMC 0 init OK!!!***
[    0.574][mmc]: erase_grp_size:0x1WrBlk * 0x200 = 0x200 Byte
[    0.579][mmc]: secure_feature 0x0
[    0.583][mmc]: secure_removal_type  0x0
[    0.587]sunxi flash init ok
script config pll_de to 864 Mhz
Not Found clk pll_video1 in script
script config pll_video to 297 Mhz
[boot]disp_init_tv
[DISP_TV] disp_init_tv enter g_tv_used
screen 0 do not support TV TYPE!
[BOOOT_DISP_TV] disp tv device_registered
unable to find regulator vcc-hdmi-18 from [pmu1_regu] or [pmu2_regu]
enable power vcc-hdmi-18, ret=-1
DRV_DISP_Init end
boot_disp.auto_hpd=1
auto hpd check has 50 times!
[disk_read_fs] no the partition
error: open disp_rsl.fex, maybe it is not exist
attched ok, mgr1<-->device1, type=2, mode=11----
ready to set mode
disp_tv_enable
[    1.428]finally, output_type=0x2, output_mode=0xb, screen_id=0x1, disp_par0
fail to find part named env
Using default environment

In: serial
Out: serial
Err: serial
--------fastboot partitions--------
mbr not exist
base bootcmd=run setargs_mmc boot_normal
bootcmd set setargs_mmc
key 0
cant find rcvy value
cant find fstbt value
no misc partition is found
to be run cmd=run setargs_mmc boot_normal
[    1.465][mmc]: MMC Device 2 not found
[    1.469][mmc]: Can not find mmc dev
[    1.473][mmc]: read first backup failed in fun sdmmc_secure_storage_read l9
sunxi_secstorage_read fail
get secure storage map err
the private part isn't exist
WORK_MODE_BOOT
adver not need show
sunxi_bmp_logo_display
[disk_read_fs] no the partition
error: open bootlogo.bmp, maybe it is not exist
sunxi bmp info error : unable to open logo file bootlogo.bmp
[    1.506]Hit any key to stop autoboot:  0
[    4.762][mmc]: mmc 0 data err 2000
[    4.765][mmc]: Read remain data
[    4.770][mmc]:  read block failed
[    4.773][mmc]: block read failed
** Can't read from device 0 **

** Unable to use mmc 0:1 for fatload **
[    4.783][mmc]: mmc 0 data err 2000
[    4.787][mmc]: Read remain data
[    4.792][mmc]:  read block failed
[    4.795][mmc]: block read failed
** Can't read from device 0 **

** Unable to use mmc 0:1 for fatload **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
sunxi#