v1.0.21 Zidoo X1 image for OPI-PC

littlestone

I've merged the v1.0.21 OTA Zidoo X1 with the v1.0.19 image, changed the host file to block hardware authentication, and changed the sys_config.sys (and the associated boot0 and u-boot) to make all USB ports work for OPI-PC as well as lowered the clock settings to keep the heat low.

The v1.0.21 firmware has KODI 15.2 from Zidoo.

Latest version (power button fixed):https://mega.nz/#!UgZnARoK!d2sTNayflCvjne_Lbs1BDiFrtyb_ke-dDdAR2FW3Yzw
Older version:
https://mega.nz/#!tkJSiCJQ!w2iraar5HBxz5tbNS6ioXgD8m38_uXNqG4XLle4FhL0

Instructions: Download the image, use PheonixCard to burn to a good SD card. The first boot takes some time, just be patient.

Credits:
vlatkokaplan - instructions on changing the sys_config.sys (http://www.orangepi.org/orangepi ... 1270&extra=page%3D1)
bronco - for the clock settings (http://www.orangepi.org/orangepi ... =724&extra=page%3D2)
cbm80 - for correcting my THS values

jmanjulian

You can disable the IR port by unloading the driver module (in terminal type the command rmmod sunxi_ir_rx) or by deleting the content of the ir config file wihch is /system/usr/keylayout/sunxi-ir.kl.
The first option is not permennant but the second is.

To the author of this image:
Please modify the config file of the image again and add the folowwing:
[wifi_para]
wifi_used             = 1
wifi_sdc_id           = 1
wifi_usbc_id          = 1
wifi_usbc_type        = 1

This enables usb wifi adapters based on rtl8188 chip. Currently the image is set to wifi_used  = 0 wifi_usbc_id = 5 and usb wifi does not get activated.

simplyngo

plz include MediaTek MT7610U (RT2860) wifi usb driver. I cant manager to connect to net in any of the roms.

pacitzu

I have not found "IPTV Simple Client" addon on Kodi.
I have to install it? Where can I find it?

littlestone

simplyngo replied at 2016-3-21 14:32
plz include MediaTek MT7610U (RT2860) wifi usb driver. I cant manager to connect to net in any of th ...

I don't know how to build from source codes, and so I'm not able to help. Sorry.

littlestone

pacitzu replied at 2016-3-21 18:47
I have not found "IPTV Simple Client" addon on Kodi.
I have to install it? Where can I find it?

I didn't touch the Kodi of this rom, so it's the same default as Zidoo has. You may get better answer from Zidoo's user forums.

cbm80

littlestone, I've just burned SD card. Are you sure all USB ports work?
My results are:
- single vertical - doesn't work at all
- lower horizontal - works like in old Zidoo - HID and pendrive
- higher horizontal - only HID works, pendrive doesn't work
What are the differences between this image and previous v19 from Android side?

littlestone

cbm80 replied at 2016-3-22 01:16
littlestone, I've just burned SD card. Are you sure all USB ports work?
My results are:
- single ver ...

v19 had very high clock rate, and I remember the upper USB didn't work at all. So I put together sys_config.fex with USB settings from Debian for OPI-PC and the lower clock settings of dvfs from bronco's. The same settings work in Beelink' v205. I've uploaded it as attached.


So if a device isn't recognized, it's likely Zidoo changed how it's handle inside its v21's Android.

cbm80

Also with CPU clock is something wrong. Zidoo V19 was clocked from 480 to 1200 MHz. This one starts from 648 MHz. Tested with A1 CPU Tool.
Temperature in idle is higher than 60C. V19 was cooler.

cbm80

Just checked your fex file:

[dvfs_table] seems to be wrong.

it should be:

1. [dvfs_table]
   
2. pmuic_type = 2
   
3. pmu_gpio0 = port:PL06<1><1><2><1>
   
4. pmu_level0 = 11300
   
5. pmu_level1 = 1100
   
6. extremity_freq = 1296000000
   
7. max_freq = 1200000000
   
8. min_freq = 480000000
   
9. LV_count = 7
   
10. LV1_freq = 1296000000
    
11. LV1_volt = 1320
    
12. LV2_freq = 1200000000
    
13. LV2_volt = 1240
    
14. LV3_freq = 1104000000
    
15. LV3_volt = 1180
    
16. LV4_freq = 1008000000
    
17. LV4_volt = 1140
    
18. LV5_freq = 960000000
    
19. LV5_volt = 1080
    
20. LV6_freq = 816000000
    
21. LV6_volt = 1020
    
22. LV7_freq = 480000000
    
23. LV7_volt = 980

Copy code

Also boot clock could be 1008.

littlestone

Thanks, cbm80, I think I took the dvfs part from one of the many test versions and didn't realize it was not the latest. Uploading the repacked version now.