ADB on One Plus

gounthar

Hi,

I finally managed to get my Orange Pi One Plus to work with the latest OrangePi_OnePlus_Android_7.0_en_gapps_v1.3.img.tar.gz.
Now, I would like to connect it through adb; I found that the port is 7100 and not 5555 like my other devices, but... It stays offline.

1. $ adb connect 192.168.1.18:7100
   
2. connected to 192.168.1.18:7100
   
3. 
   
4. me@myPC ~
   
5. $ adb devices
   
6. List of devices attached
   
7. 192.168.1.18:7100       offline

Copy code

Most of the times (on other Android devices), I get a popup on the screen asking to approve or reject the computer trying to connect.
This time, I didn't get anything.
What is the procedure to connect to the One Plus running Android so that I can get online and not offline?

Should I try to connect it with USB first? Is there a pin to move somewhere on the card? How could I find the drivers so that Windows can see it as an Android device?

Thanks.

gounthar

Tonight at home, the 7100 port is not available anymore.
I tried to download Aptoide, but I don't know where the downloaded files go. Not in the downloads folder for sure...

gounthar

I scanned all the ports of my device, but found none open:

1. Nmap scan report for 192.168.0.11
   
2. Host is up (0.014s latency).
   
3. All 65535 scanned ports on 192.168.0.11 are closed
   
4. MAC Address: 90:5F:2E:89:64:43 (TCT mobile)
   
5. 
   
6. Nmap scan report for 192.168.0.18
   
7. Host is up (0.011s latency).
   
8. All 65535 scanned ports on 192.168.0.18 are closed
   
9. MAC Address: C6:2B:FE:CC:A2:15 (Unknown)

Copy code

Werner

Just curios. When you check your /proc/loadavg is it actually lower than 3?
Sorry, this has actually nothing to do with your issue, but I am stuck with another problem described here and would appreciate if you could give this a quick check when the device has been idle for a while.

http://www.orangepi.org/orangepi ... o=lastpost#lastpost

gounthar

Sorry, but as long as I can't connect to the One Plus through network or adb, I am not able to see the load average. There isn't even a shell within the image, I can't do anything with it.

gounthar

Well, I can connect through ADB with no power thanks to OTG, but when I want to tell the One Plus that I want to connect through the network, the board just doesn't care:

1. adb -s 20080411 shell
   
2. petrel-p1:/ # setprop persists.adb.tcp.port 5555
   
3. petrel-p1:/ # getprop persists.adb.tcp.port
   
4. 5555
   
5. petrel-p1:/ # sync && reboot
   

Copy code

Then:

1. adb devices
   
2. List of devices attached
   
3. 20080411        device
   
4. adb connect 192.168.0.14
   
5. unable to connect to 192.168.0.14:5555: Connection refused
   

Copy code

I have to reset the adb through network:

1. adb -s 20080411 tcpip 5555
   
2. restarting in TCP mode port: 5555
   
3. ~ openstf$ adb connect 192.168.0.14
   
4. connected to 192.168.0.14:5555
   
5. ~ openstf$ adb devices
   
6. List of devices attached
   
7. 192.168.0.14:5555       device
   
8. 20080411        device

Copy code

So... I am connected twice to this device (USB and network).

gounthar

So... To answer your question, I launched this command while the device was doing... nothing:

1. petrel-p1:/ # cat /proc/loadavg
   
2. 3.15 3.29 1.82 3/1033 13165
   

Copy code