Orange PI- no video and shuting down after 30-40 sec

dani91ro · Published in 2016-2-8 21:42:01

Hello,
I am using Orange PI over a month and now does want to boot. Every thing works fine until last week when he "died". I am using 16 GB Class10 Micro USB card, power supply of 5V/3A. When i powered up the red led is on and ethernet port led is on, and afer 30-45s the leds from the ethernet port start to blink and stop(the red led is still on). I change the power supply, OS and TF card and the same think happend.I measure the current consumption and the board reach 600mA then the ethernet port leds stops. I connect orange pi to a PC terminal to see the boot log. This is the log:

HELLO! BOOT0 is starting!
boot0 version : 4.0.0
fel_flag = 0x00000000
rtc[0] value = 0x00000000
rtc[1] value = 0x00000000
rtc[2] value = 0x00000000
rtc[3] value = 0x00000000
rtc[4] value = 0x00000000
rtc[5] value = 0x00000000
rtc[6] value = 0x00000000
rtc[7] value = 0x00000000
DRAM DRIVE INFO: V0.8
DRAM Type = 3 (2

DR2,3

DR3,6

PDDR2,7

PDDR3)
DRAM CLK = 672 MHz
DRAM zq value: 003b3bfb
READ DQS LCDL = 001e1e1e
DRAM SIZE =1024 M
odt delay
dram size =1024
card boot number = 0
card no is 0
sdcard 0 line count 4
[mmc]: mmc driver ver 2014-12-10 21:20:39
[mmc]: ***Try SD card 0***
[mmc]: SD/MMC Card: 4bit, capacity: 15193MB
[mmc]: vendor: Man 00035344 Snr 13f50efc
[mmc]: product: SL16G
[mmc]: revision: 8.0
[mmc]: ***SD/MMC 0 init OK!!!***
sdcard 0 init ok
The size of uboot is 000dc000.
sum=ede66ee7
src_sum=ede66ee7
Succeed in loading uboot from sdmmc flash.
Ready to disable icache.
Jump to secend Boot.
SUNXI_NORMAL_MODE
already secure mode

[    0.359]

U-Boot 2011.09-rc1 (Jun 21 2015 - 19:33:17) Allwinner Technology

[    0.366]version: 1.1.0
normal mode
[    0.374]pmbus: ready
not set main pmu id
axp_probe error
[    0.389]PMU: pll1 1200 Mhz,PLL6=600 Mhz
AXI=400 Mhz,AHB=200 Mhz, APB1=100 Mhz
sid read already
fel key new mode
run key detect
no key found
no key input
dram_para_set start
dram_para_set end
normal mode
[    0.419]DRAM:  1 GiB
relocation Offset is: 35af9000
[box standby] read rtc = 0x0
[box_start_os] mag be start_type no use
user_gpio config
user_gpio ok
gic: normal or no secure os mode
workmode = 0
MMC:    0
[    0.494][mmc]: mmc driver ver 2014-12-10 9:23:00
[    0.499][mmc]: get sdc_phy_wipe fail.
[    0.503][mmc]: get sdc0 sdc_erase fail.
[    0.507][mmc]: get sdc_f_max fail,use default 50000000Hz
[    0.512][mmc]: get sdc_ex_dly_used fail,use default dly
[    0.518][mmc]: SUNXI SD/MMC: 0
[    0.531][mmc]: *Try SD card 0*
[    0.575][mmc]: CID 0x3534453 0x4c313647 0x8013f50e 0xfc00fb05
[    0.580][mmc]: mmc clk 50000000
[    0.584][mmc]: SD/MMC Card: 4bit, capacity: 15193MB
[    0.589][mmc]: boot0 capacity: 0KB,boot1 capacity: 0KB
[    0.594][mmc]: ***SD/MMC 0 init OK!!!***
[    0.603][mmc]: erase_grp_size:0x1WrBlk * 0x200 = 0x200 Byte
[    0.608][mmc]: secure_feature 0x0
[    0.612][mmc]: secure_removal_type  0x0
[    0.616]sunxi flash init ok
script config pll_de to 864 Mhz
Not Found clk pll_video1 in script
script config pll_video to 297 Mhz
[boot]disp_init_tv
[DISP_TV] disp_init_tv enter g_tv_used
screen 0 do not support TV TYPE!
[BOOOT_DISP_TV] disp tv device_registered
unable to find regulator vcc-hdmi-18 from [pmu1_regu] or [pmu2_regu]
enable power vcc-hdmi-18, ret=-1
DRV_DISP_Init end
boot_disp.auto_hpd=1
auto hpd check has 50 times!
[disk_read_fs] no the partition
error: open disp_rsl.fex, maybe it is not exist
attched ok, mgr1<-->device1, type=2, mode=11----
ready to set mode
disp_tv_enable
[    1.460]finally, output_type=0x2, output_mode=0xb, screen_id=0x1, disp_para=0x20b0000
fail to find part named env
Using default environment

In: serial
Out: serial
Err: serial
--------fastboot partitions--------
mbr not exist
base bootcmd=run setargs_mmc boot_normal
bootcmd set setargs_mmc
key 0
cant find rcvy value
cant find fstbt value
no misc partition is found
to be run cmd=run setargs_mmc boot_normal
[    1.497][mmc]: MMC Device 2 not found
[    1.501][mmc]: Can not find mmc dev
[    1.505][mmc]: read first backup failed in fun sdmmc_secure_storage_read line 1849
sunxi_secstorage_read fail
get secure storage map err
the private part isn't exist
WORK_MODE_BOOT
adver not need show
sunxi_bmp_logo_display
[disk_read_fs] no the partition
error: open bootlogo.bmp, maybe it is not exist
sunxi bmp info error : unable to open logo file bootlogo.bmp
[    1.538]Hit any key to stop autoboot:  3 2 1 0
## Booting kernel from Legacy Image at 40007800 ...
Image Name: Linux-3.4.39
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 10915552 Bytes = 10.4 MiB
Load Address: 40008000
Entry Point:  40008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
[    5.444][mmc]: MMC Device 2 not found
[    5.448][mmc]:  mmc  not find,so not exit
[    5.452]
Starting kernel ...

[sun8i_fixup]: From boot, get meminfo:

Start: 0x40000000

Size: 1024MB

ion_carveout reserve: 160m@0 256m@0 130m@1 200m@1

ion_reserve_common: ion reserve: [0x70000000, 0x80000000]!

Daniel

dani91ro · Published in 2016-2-8 21:44:19

This is the second part of the log:

[ 0.000000] Booting Linux on physical CPU 0

[ 0.000000] Initializing cgroup subsys cpu

[ 0.000000] Linux version 3.4.39 (boris@UbuntuMate) (gcc version 4.6.3 20120201 (prerelease) (crosstool-NG linaro-1.13.1-2012.02-20120222 - Linaro GCC 2012.02) ) #1 SMP PREEMPT Mon Oct 12 12:02:29 CEST 2015

[ 0.000000] Ignoring tag cmdline (using the default kernel command line)

[ 0.000000] bootconsole [earlycon0] enabled

[ 0.000000] cma: CMA: reserved 256 MiB at 70000000

[ 0.000000] Memory policy: ECC disabled, Data cache writealloc

[ 0.000000] On node 0 totalpages: 262144

[ 0.000000] free_area_init_node: node 0, pgdat c1000cc0, node_mem_map c10dd000

[ 0.000000] Normal zone: 1710 pages used for memmap

[ 0.000000] Normal zone: 0 pages reserved

[ 0.000000] Normal zone: 192850 pages, LIFO batch:31

[ 0.000000] HighMem zone: 594 pages used for memmap

[ 0.000000] HighMem zone: 66990 pages, LIFO batch:15

[ 0.000000] script_init enter!

[ 0.000000] script_init exit!

[ 0.000000] PERCPU: Embedded 8 pages/cpu @c19f3000 s11840 r8192 d12736 u32768

[ 0.000000] pcpu-alloc: s11840 r8192 d12736 u32768 alloc=8*4096

[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 259840

[ 0.000000] Kernel command line: earlyprintk=ttyS0,115200 loglevel=8 initcall_debug=0 console=ttyS0,115200 console=tty0 init=/init

[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)

[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)

[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)

[ 0.000000] Memory: 1024MB = 1024MB total

[ 0.000000] Memory: 758680k/758680k available, 289896k reserved, 8192K highmem

[ 0.000000] Virtual kernel memory layout:

[ 0.000000]    vector  : 0xffff0000 - 0xffff1000 ( 4 kB)

[ 0.000000]    fixmap  : 0xfff00000 - 0xfffe0000 ( 896 kB)

[ 0.000000]    vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)

[ 0.000000]    lowmem  : 0xc0000000 - 0xef800000 ( 760 MB)

[ 0.000000]    pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)

[ 0.000000]    modules : 0xbf000000 - 0xbfe00000 (  14 MB)

[ 0.000000]    .text : 0xc0008000 - 0xc0986378 (9721 kB)

[ 0.000000]    .init : 0xc0987000 - 0xc0f86e40 (6144 kB)

[ 0.000000]    .data : 0xc0f88000 - 0xc1003738 ( 494 kB)

[ 0.000000]       .bss : 0xc1003eec - 0xc10dc400 ( 866 kB)

[ 0.000000] Preemptible hierarchical RCU implementation.

[ 0.000000]    Additional per-CPU info printed with stalls.

[ 0.000000] NR_IRQS:544

[ 0.000000] Architected local timer running at 24.00MHz.

[ 0.000000] Switching to timer-based delay loop

[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms

[ 0.000000] Console: colour dummy device 80x30

[ 0.000000] console [tty0] enabled, bootconsole disabled

[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.4.39 (boris@UbuntuMate) (gcc version 4.6.3 20120201 (prerelease) (crosstool-NG linaro-1.13.1-2012.02-20120222 - Linaro GCC 2012.02) ) #1 SMP PREEMPT Mon Oct 12 12:02:29 CEST 2015
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: sun8i
[ 0.000000] Ignoring tag cmdline (using the default kernel command line)
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] cma: CMA: reserved 256 MiB at 70000000
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] On node 0 totalpages: 262144
[ 0.000000] free_area_init_node: node 0, pgdat c1000cc0, node_mem_map c10dd000
[ 0.000000] Normal zone: 1710 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 192850 pages, LIFO batch:31
[ 0.000000] HighMem zone: 594 pages used for memmap
[ 0.000000] HighMem zone: 66990 pages, LIFO batch:15
[ 0.000000] script_init enter!
[ 0.000000] script_init exit!
[ 0.000000] PERCPU: Embedded 8 pages/cpu @c19f3000 s11840 r8192 d12736 u32768
[ 0.000000] pcpu-alloc: s11840 r8192 d12736 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 259840
[ 0.000000] Kernel command line: earlyprintk=ttyS0,115200 loglevel=8 initcall_debug=0 console=ttyS0,115200 console=tty0 init=/init
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 1024MB = 1024MB total
[ 0.000000] Memory: 758680k/758680k available, 289896k reserved, 8192K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000]    vector  : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000]    fixmap  : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000]    vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000]    lowmem  : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000]    pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000]    modules : 0xbf000000 - 0xbfe00000 (  14 MB)
[ 0.000000]    .text : 0xc0008000 - 0xc0986378 (9721 kB)
[ 0.000000]    .init : 0xc0987000 - 0xc0f86e40 (6144 kB)
[ 0.000000]    .data : 0xc0f88000 - 0xc1003738 ( 494 kB)
[ 0.000000]       .bss : 0xc1003eec - 0xc10dc400 ( 866 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000]    Additional per-CPU info printed with stalls.
[ 0.000000] NR_IRQS:544
[ 0.000000] Architected local timer running at 24.00MHz.
[ 0.000000] Switching to timer-based delay loop
[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [tty0] enabled, bootconsole disabled

dani91ro · Published in 2016-2-8 21:45:22

And this is the third part of the log:
[ 0.019915] Calibrating delay loop (skipped), value calculated using timer frequency.. 4800.00 BogoMIPS (lpj=24000000)
[ 0.019969] pid_max: default: 32768 minimum: 301
[ 0.020241] Mount-cache hash table entries: 512
[ 0.021123] Initializing cgroup subsys cpuacct
[ 0.021153] Initializing cgroup subsys freezer
[ 0.021199] CPU: Testing write buffer coherency: ok
[ 0.021253] ftrace: allocating 26203 entries in 77 pages
[ 0.050269] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.050301] [sunxi_smp_prepare_cpus] enter
[ 0.050343] Setting up static identity map for 0x406d2af0 - 0x406d2b48
[ 0.051184] CPU1: Booted secondary processor
[ 0.051184] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.051318] CPU2: Booted secondary processor
[ 0.051318] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.051318] CPU3: Booted secondary processor
[ 0.051318] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.060171] Brought up 4 CPUs
[ 0.060254] SMP: Total of 4 processors activated (19200.00 BogoMIPS).
[ 0.060834] devtmpfs: initialized
[ 0.063130] wakeup src cnt is : 1.
[ 0.063149] [exstandby]leave extended_standby_enable_wakeup_src : event 0x800000
[ 0.063173] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpio_map 0x0
[ 0.063196] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpio_group 0x40
[ 0.063221] sunxi pm init
[ 0.063353] pinctrl core: initialized pinctrl subsystem
[ 0.073992] NET: Registered protocol family 16
[ 0.074656] DMA: preallocated 2048 KiB pool for atomic coherent allocations
[ 0.074656] script_sysfs_init success
[ 0.074656] sunxi_dump_init success
[ 0.074656] gpiochip_add: registered GPIOs 0 to 383 on device: sunxi-pinctrl
[ 0.074656] sunxi-pinctrl sunxi-pinctrl: initialized sunXi PIO driver
[ 0.074656] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.074656] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.074656] script config pll_video to 297 Mhz
[ 0.074656] script config pll_de to 864 Mhz
[ 0.074656] script config pll_ve to 402 Mhz
[ 0.074656] sunxi_default_clk_init
[ 0.074656] try to set pll6ahb1 to 200000000
[ 0.074656] try to set ahb clk source to pll6ahb1
[ 0.074656] set ahb clk source to pll6ahb1
[ 0.074656] try to set ahb1 to 200000000
[ 0.074656] try to set apb1 to 100000000
[ 0.074955] ===fe3o4==== sunxi_root_procfs_attach ret:0
[ 0.080510] bio: create slab <bio-0> at 0
[ 0.080510] [ARISC] :sunxi-arisc driver v1.04
[ 0.095237] [ARISC] :arisc version: [v0.1.34]
[ 0.173075] [ARISC] :sunxi-arisc driver v1.04 startup succeeded
[ 0.180382] SCSI subsystem initialized
[ 0.180566] usbcore: registered new interface driver usbfs
[ 0.180642] usbcore: registered new interface driver hub
[ 0.180683] usbcore: registered new device driver usb
[ 0.180683] twi_chan_cfg()335 - [twi0] has no twi_regulator.
[ 0.180683] twi_chan_cfg()335 - [twi1] has no twi_regulator.
[ 0.180683] twi_chan_cfg()335 - [twi2] has no twi_regulator.
[ 0.180724] Linux video capture interface: v2.00
[ 0.180916] Advanced Linux Sound Architecture Driver Version 1.0.25.
[ 0.181396] Bluetooth: Core ver 2.16
[ 0.181446] NET: Registered protocol family 31
[ 0.181468] Bluetooth: HCI device and connection manager initialized
[ 0.181495] Bluetooth: HCI socket layer initialized
[ 0.181515] Bluetooth: L2CAP socket layer initialized
[ 0.181556] Bluetooth: SCO socket layer initialized
[ 0.181763] cfg80211: Calling CRDA to update world regulatory domain
[ 0.181836] Switching to clocksource arch_sys_counter
[ 0.192049] FS-Cache: Loaded
[ 0.192331] CacheFiles: Loaded
[ 0.202178] NET: Registered protocol family 2
[ 0.202440] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.202966] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.204582] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[ 0.205373] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.205397] TCP: reno registered
[ 0.205417] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.205461] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.205734] NET: Registered protocol family 1
[ 0.206078] RPC: Registered named UNIX socket transport module.
[ 0.206105] RPC: Registered udp transport module.
[ 0.206123] RPC: Registered tcp transport module.
[ 0.206141] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.544917] hw perfevents: enabled with ARMv7 Cortex_A7 PMU driver, 5 counters available
[ 0.545064] sunxi_reg_init enter
[ 0.545787] audit: initializing netlink socket (disabled)
[ 0.545848] type=2000 audit(0.540:1): initialized
[ 0.548951] highmem bounce pool size: 64 pages
[ 0.549897] NFS: Registering the id_resolver key type
[ 0.550302] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 0.550961] NTFS driver 2.1.30 [Flags: R/W].
[ 0.551085] fuse init (API version 7.18)
[ 0.551849] Btrfs loaded
[ 0.551882] msgmni has been set to 1465
[ 0.552910] io scheduler noop registered
[ 0.552935] io scheduler deadline registered
[ 0.553016] io scheduler cfq registered (default)
[ 0.553385] [DISP]disp_module_init
[ 0.553666] cmdline,disp=
[ 0.562057] [DISP] Fb_map_kernel_logo,line:925:Fb_map_kernel_logo failed!
[ 0.574800] Console: switching to colour frame buffer device 160x45
[ 0.588476] [DISP]disp_module_init finish
[ 0.588755] sw_uart_get_devinfo()1503 - uart0 has no uart_regulator.
[ 0.588906] sw_uart_get_devinfo()1503 - uart2 has no uart_regulator.
[ 0.589051] sw_uart_get_devinfo()1503 - uart3 has no uart_regulator.
[ 0.589598] uart0: ttyS0 at MMIO 0x1c28000 (irq = 32) is a SUNXI
[ 0.589742] sw_uart_pm()890 - uart0 clk is already enable
[ 0.589872] sw_console_setup()1233 - console setup baud 115200 parity n bits 8, flow n
[ 0.781871] console [ttyS0] enabled
[ 1.217997] uart2: ttyS2 at MMIO 0x1c28800 (irq = 34) is a SUNXI
[ 1.381273] uart3: ttyS3 at MMIO 0x1c28c00 (irq = 35) is a SUNXI
[ 1.531165] sunxi_cmatest_init enter
[ 1.680106] sunxi_cmatest_init success
[ 1.846979] loop: module loaded
[ 1.958552] sunxi_spi_chan_cfg()1355 - [spi-0] has no spi_regulator.
[ 1.969433] sunxi_spi_chan_cfg()1355 - [spi-1] has no spi_regulator.
[ 1.980667] spi spi0: master is unqueued, this is deprecated
[ 1.990927] tun: Universal TUN/TAP device driver, 1.6

dani91ro · Published in 2016-2-8 21:46:43

and the fourth one:
[ 2.000190] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 2.011468] PPP generic driver version 2.4.2
[ 2.020029] PPP BSD Compression module registered
[ 2.028870] PPP Deflate Compression module registered
[ 2.040194] PPP MPPE Compression module registered
[ 2.049122] NET: Registered protocol family 24
[ 2.057654] PPTP driver version 0.8.5
[ 2.065464] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.096505] sunxi-ehci sunxi-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driveontroller (OHCI) Driver
[ 2.783614] sunxi-ohci sunxi-ohci.3: new USB bus registered, assigned bus number 7
[ 2.796012] sunxi-ohci sunxi-ohci.3: irq 109, io mem 0xf1c1c400
[ 2.864449] hub 7-0:1.0: USB hub found
[ 2.872537] hub 7-0:1.0: 1 port detected
[ 2.901073] sunxi-ohci sunxi-ohci.4: SW USB2.0 'Open' Host Controller (OHCI) Driver
[ 2.913594] sunxi-ohci sunxi-ohci.4: new USB bus registered, assigned bus number 8
[ 2.926035] sunxi-ohci sunxi-ohci.4: irq 111, io mem 0xf1c1d400
[ 2.994468] hub 8-0:1.0: USB hub found
[ 3.002602] hub 8-0:1.0: 1 port detected
[ 3.011143] Initializing USB Mass Storage driver...
[ 3.020618] usbcore: registered new interface driver usb-storage
[ 3.031186] USB Mass Storage support registered.
[ 3.040299] usbcore: registered new interface driver ums-alauda
[ 3.050855] usbcore: registered new interface driver ums-cypress
[ 3.061500] usbcore: registered new interface driver ums-datafab
[ 3.072029] usbcore: registered new interface driver ums_eneub6250
[ 3.082685] usbcore: registered new interface driver ums-freecom
[ 3.093091] usbcore: registered new interface driver ums-isd200
[ 3.103377] usbcore: registered new interface driver ums-jumpshot
[ 3.113842] usbcore: registered new interface driver ums-karma
[ 3.123955] usbcore: registered new interface driver ums-onetouch
[ 3.134261] usbcore: registered new interface driver ums-realtek
[ 3.144388] usbcore: registered new interface driver ums-sddr09
[ 3.154357] usbcore: registered new interface driver ums-sddr55
[ 3.164291] usbcore: registered new interface driver ums-usbat
[ 3.174120] usbcore: registered new interface driver usbserial
[ 3.183838] usbserial: USB Serial Driver core
[ 3.191878] usbcore: registered new interface driver option
[ 3.201264] USB Serial support registered for GSM modem (1-port)
[ 3.211692] file system registered
[ 3.220194] android_usb gadget: Mass Storage Function, version: 2009/09/11
[ 3.231121] android_usb gadget: Number of LUNs=3
[ 3.239509]  lun0: LUN: removable file: (no medium)
[ 3.248172]  lun1: LUN: removable file: (no medium)
[ 3.256730]  lun2: LUN: removable file: (no medium)
[ 3.265506] android_usb gadget: android_usb ready
[ 3.273983]  uinput result 0 , vmouse_init
[ 3.282164] mousedev: PS/2 mouse device common for all mice
[ 3.291657] sunxikbd_init failed.
[ 3.298448] ls_fetch_sysconfig_para: type err  device_used = 0.
[ 3.308187] =========script_get_err============
[ 3.316269] ltr_init: ls_fetch_sysconfig_para err.
[ 3.325087] sunxi-rtc sunxi-rtc: rtc core: registered sunxi-rtc as rtc0
[ 3.335625] i2c /dev entries driver
[ 3.342897] IR RC5(x) protocol handler initialized
[ 3.351380] sunxi tsc version 0.1
[ 3.358222] tscdev_init: tsc driver is disabled
[ 3.366375] sunxi cedar version 0.1
[ 3.373427] [cedar]: install start!!!
[ 3.380643] [cedar]: install end!!!
[ 3.387443] sunxi_wdt_init_module: sunxi WatchDog Timer Driver v1.0
[ 3.397512] sunxi_wdt_probe: devm_ioremap return wdt_reg 0xf1c20ca0, res->start 0x01c20ca0, res->end 0x01c20cbf
[ 3.408857] sunxi_wdt_probe: initialized (g_timeout=16s, g_nowayout=0)
[ 3.422374] wdt_enable, write reg 0xf1c20cb8 val 0x00000000
[ 3.431730] timeout_to_interv, line 167
[ 3.439101] interv_to_timeout, line 189
[ 3.446428] wdt_set_tmout, write 0x000000b0 to mode reg 0xf1c20cb8, actual timeout 16 sec
[ 3.459038] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[ 3.471778] Bluetooth: HCI UART driver ver 2.2
[ 3.480380] [mmc]: SD/MMC/SDIO Host Controller Driver(v1.109 2014-12-4 20:51) Compiled in Oct 12 2015 at 12:00:18
[ 3.495420] [mmc]: get mmc0's sdc_power is null!
[ 3.504199] [mmc]: get mmc1's sdc_power is null!
[ 3.512961] [mmc]: get mmc1's 2xmode ok, val = 1
[ 3.521730] [mmc]: get mmc1's ddrmode ok, val = 1
[ 3.530639] [mmc]: MMC host used card: 0x3, boot card: 0x0, io_card 2
[ 3.542386] [mmc]: sdc0 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 3.558877] [mmc]: sdc1 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 3.574905] sunxi_leds_fetch_sysconfig_para script_parser_fetch "leds_para" leds_used = -1063626804
[ 3.588601] =========script_get_err============
[ 3.598245] usbcore: registered new interface driver usbhid
[ 3.607945] usbhid: USB HID core driver
[ 3.619142] asoc: sndcodec <-> sunxi-codec mapping ok
[ 3.631013] asoc: sndhdmi <-> sunxi-hdmiaudio.0 mapping ok
[ 3.641279] oprofile: using arm/armv7-ca7
[ 3.649293] mplementor 41 architecture 2 part 30 variant 7 rev 5
[ 3.938307] ThumbEE CPU extension supported.
[ 3.945954] Registering SWP/SWPB emulation handler
[ 3.954819] cmdline,disp=
[ 3.960647] [HDMI] power vcc-hdmi-18
[ 3.998096] sunxi-rtc sunxi-rtc: setting system clock to 1970-01-01 00:00:10 UTC (10)
[ 4.009662] ths_fetch_sysconfig_para: type err  device_used = 1.
[ 4.020345] CPU Budget:Register notifier
[ 4.027545] CPU Budget:register Success
[ 4.034600] sunxi-budget-cooling sunxi-budget-cooling: Cooling device registered: thermal-budget-0
[ 4.049747] [rf_pm]: select module num is 7
[ 4.057371] [rf_pm]: module power0 name vcc-wifi-33
[ 4.065765] [rf_pm]: failed to fetch module_power1
[ 4.074059] [rf_pm]: mod has no chip_en gpio
[ 4.081721] [rf_pm]: failed to fetch lpo_use_apclk
[ 4.089916] [rf_pm]: regulator on.
[ 4.096530] [wifi_pm]: no wifi used in configuration
[ 4.104870] ALSA device list:
[ 4.110943] #0: audiocodec
[ 4.116869] #1: sndhdmi
[ 4.122560] Warning: unable to open an initial console.
[ 4.135167] Freeing init memory: 6140K
[ 4.545072] [mmc]: mmc 0 detect change, present 1
[ 4.600119] [DISP] disp_device_attached_and_enable,line:159:attched ok, mgr0<-->device0, type=4, mode=5
[ 5.050138] [mmc]: sdc0 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 5.071142] [mmc]: sdc0 power_supply is null
[ 5.100119] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 5.132365] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 52,  RTO !!
[ 5.146021] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 52,  RTO !!
[ 5.163799] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 5.181226] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 5.197613] *******************Try sdio*******************
[ 5.209268] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5,  RTO !!
[ 5.222972] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5,  RTO !!
[ 5.236607] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5,  RTO !!
[ 5.250207] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5,  RTO !!
[ 5.262918] *******************Try sd *******************
[ 5.274259] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 5.289408] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 5.306853] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 5.381556] [mmc]: sdc0 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 5.402610] [mmc]: sdc0 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B
[ 5.417265] [mmc]: sdc0 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B
[ 5.431914] [mmc]: sdc0 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B
[ 5.446439] mmc0: new high speed SDHC card at address aaaa
[ 5.457140] mmcblk0: mmc0:aaaa SL16G 14.8 GiB
[ 5.476170]  mmcblk0: p1 p2
[ 5.483697] *******************sd init ok*******************

dani91ro · Published in 2016-2-8 21:47:01

and the last one:
[ 10.561621] systemd-udevd[109]: starting version 215
[ 11.849873] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 12.752882] init: plymouth-upstart-bridge main process (155) terminated with status 1
[ 12.765128] init: plymouth-upstart-bridge main process ended, respawning
[ 12.801685] init: plymouth-upstart-bridge main process (165) terminated with status 1
[ 12.813947] init: plymouth-upstart-bridge main process ended, respawning
[ 12.839874] init: plymouth-upstart-bridge main process (168) terminated with status 1
[ 12.851778] init: plymouth-upstart-bridge main process ended, respawning
[ 12.879581] init: plymouth-upstart-bridge main process (170) terminated with status 1
[ 12.891545] init: plymouth-upstart-bridge main process ended, respawning
[ 12.903098] init: ureadahead main process (158) terminated with status 5
[ 13.196076] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
* Starting Mount filesystems on boot * Stopping Send an event to indicate plymouth is up * Starting bluetooth daemon * Starting SystemD login management service * Starting mDNS/DNS-SD daemon * Starting Reload cups, upon starting avahi-daemon to make sure remote queues are populated * Stopping cold plug devices * Stopping log initial device creation * Starting configure network device security* Starting Mount network filesystems * Stopping Reload cups, upon starting avahi-daemon to make sure remote queues are populated * Starting configure virtual network devices * Starting configure network device k filesystems * Stopping Failsafe Boot Delay4G[ OK ]

* Starting System V initialisation compatibility
* Starting early crypto disks...
* Starting Bridge socket events into upstart * Setting up X socket directories...
* Stopping System V initialisation compatibility
* Starting NTP server ntpd

* Restoring resolver state...    ng System V runlevel compatibility * Starting regular background program processing daemon

Ubuntu 14.04.1 LTS orangepi ttyS0